SMACNA Subscriptions

- Free Trial - Webinar - Feedback - FAQ

Overview

Cart (0)

eLibrary > Fibrous Glass Duct Construction Standards, 7th Edition >

Fibrous Glass Duct Construction Standards, 7th Edition, 2003

Expand All TOC Search:

FOREWORD
REFERENCES
INTRODUCTION
NOTICE TO USERS OF THIS PUBLICATION
TABLE OF CONTENTS
TABLES
FIGURES
CHAPTER 1 INTRODUCTION [Go to Page]
1.1 MODEL PROJECT SPECIFICATION
CHAPTER 2 DUCT PERFORMANCE CHARACTERISTICS [Go to Page]
2.1 FIBROUS GLASS DUCT PERFORMANCE CHARACTERISTICS
2.2 USE IN MEDICAL FACILITIES
2.3 OTHER PERFORMANCE CHARACTERISTICS
CHAPTER 3 SPECIFICATIONS AND CLOSURE [Go to Page]
3.1 GENERAL SPECIFICATION REQUIREMENTS
3.2 CLOSURES
FIGURE 3-1 CLOSURES
FIGURE 3-2 CLOSURES (CONTINUED)
CHAPTER 4 FITTINGS AND CONNECTIONS [Go to Page]
FIGURE 4-1 ONE-WAY TRANSITIONS
FIGURE 4-2 TWO-WAY TRANSITIONS
FIGURE 4-3 ELBOWS
FIGURE 4-4 OFFSET
FIGURE 4-5 TEES AND BRANCH TAKE OFFS
FIGURE 4-6 90 DEGREE ELBOWS WITH TURNING VANES
FIGURE 4-7 ENTRY BRANCH AND SPLITTER DAMPER
FIGURE 4-8 END CAPS
FIGURE 4-9 FLANGE ON OPENING
FIGURE 4-10 SHEET METAL AND EQUIPMENT CONNECTION DETAILS
FIGURE 4-11 SHEET METAL AND EQUIPMENT CONNECTION DETAILS (CONTINUED)
FIGURE 4-12 REGISTER AND GRILLE ATTACHMENT
FIGURE 4-13 DIFFUSER CONNECTION
CHAPTER 5 REINFORCEMENT [Go to Page]
FIGURE 5-1 TIE ROD TERMINATION METHODS
FIGURE 5-2 TIE ROD REINFORCEMENT
Table 5-1 Tie Rod System Reinforcement Schedule
FIGURE 5-2M TIE ROD REINFORCEMENT
Table 5-1M Tie Rod System Reinforcement Schedule
FIGURE 5-3 TIE ROD REINFORCEMENT AT JOINT
FIGURE 5-4 CHANNEL REINFORCEMENT EXAMPLES— POSITIVE PRESSURE
Table 5-2 Channel System Reinforcement Schedule
Table 5-2M Channel System Reinforcement Schedule
FIGURE 5-5 PARTIAL WRAP-AROUND REINFORCEMENT
Table 5-3 Partial Wrap-Around Reinforcement Schedule
FIGURE 5-6 PARTIAL WRAP-AROUND REINFORCEMENT
Table 5-3M Partial Wrap-Around Reinforcement Schedule
FIGURE 5-7 CHANNEL REINFORCEMENT— NEGATIVE PRESSURE SYSTEMS
FIGURE 5-8 FITTING REINFORCEMENT—90 DEGREE ELBOWS
FIGURE 5--9 REINFORCEMENT—90 DEGREE ELBOWS
FIGURE 5-10 REINFORCEMENT—BRANCH CONNECTIONS
FIGURE 5-11 REINFORCEMENT—TEES
FIGURE 5-12 REINFORCEMENT—OFFSETS AND MITERED ELBOWS
FIGURE 5-13 REINFORCEMENTS—TRANSITIONS
FIGURE 5-14 REINFORCEMENT—ACCESS DOORS
FIGURE 5-15 REINFORCEMENT—END CAPS
CHAPTER 6 HANGERS AND SUPPORTS [Go to Page]
FIGURE 6-1 ALLOWABLE HANGER SPACING, STRAIGHT DUCT, 3 IN. (75 MM) WIDE CHANNEL
Table 6-1 Maximum Hanger Spacing By Duct Size ID
Table 6-2 Channel Selection
FIGURE 6-2 HANGING DUCT
FIGURE 6-3 HANGING DUCT FITTINGS UP TO 48 IN. (1.22 M) WIDTH
FIGURE 6-4 HANGING DUCT FITTINGS UP TO 48 IN. (1.22 MM) WIDTH (CONTINUED)
FIGURE 6-5 VERTICAL RISER SUPPORT
FIGURE 6-6 ELECTRIC HEATER SUPPORT
FIGURE 6-7 VOLUME DAMPER INSTALLATION
APPENDIX [Go to Page]
CONTRIBUTORS TO FORMER EDITIONS OF THE SMACNA FIBROUS GLASS DUCT CONSTRUCTION STANDARDS [Go to Page]
Committees for First and Second Editions
Committees for Third Edition
Committees for Fourth Edition
Committees for Fifth Edition
Committees for Sixth Edition
Inspection Checklist for Fibrous Glass Duct System Installation
INDEX [Go to Page]

Email *
Password *
Confirm *
First Name *
Last Name *
Title
Company Name *
Company Size *
Industry *
Address *
Address 2
City *
State *	Zip *
Country *
Phone *
How did you hear about SMACNA Subscriptions? *

Name
Email
Phone
State
Jurisdiction
File Upload	Remove Add More
Notes

Username:
Password:

SMACNA Subscriptions Free Trial

Fibrous Glass Duct Construction Standards, 7th Edition, 2003